Model Change Bulletin MCB # 3 (1/6/00) OCD5 (00006) An error was found in the calculation of the virtual source distance for sigma-z for the case where neutral or unstable conditions at a source over water coincide with stable conditions at a receptor over land. The calculation scheme in lines VIR01040 through VIR01100 in the VIRTUAL subroutine in OCD did not present a valid solution for those cases. This is due to the fact that under stable conditions the value of sigma-z reaches a maximum value at a certain downwind distance. If the value of sigma-z at the point where the plume enters the thermal internal boundary layer (TIBL) is higher than this maximum value, there can be no solution for the virtual distance calculation. The routine used in the program therefore resulted in an incorrect values, ones which are lower than what is physically possible. The problem with the virtual distance calculation was solved by applying instead the scheme in lines VIR01120 through VIR01240. This routine uses the Briggs default turbulent intensity values for the onshore stability and obtains the virtual distance by solving a quadratic equation. If no solution is reached in the stable case, VIRTZ is set to zero and the value of sigma-z at the receptor is forced to be the same as the sigma-z value at the TIBL interface. This is because when sigma-z at the TIBL interface exceeds the highest value that can be realized over land for the given stability category, the plume cannot grow any further once it enters the TIBL. Since this virtual distance calculation was written for use in the cases where the overland turbulent intensity is given in the meteorological input file, a dummy variable had to be introduced so that this routine could also be applied to the case where the Briggs default values had to be used. An error was also found in the calculation of the stable layer mixing height cap in the MIXT (mixing height) subroutine. The code incorrectly applied the mixing height cap to stability categories less than or equal to 5 instead of to categories equal to or greater than 5. The following changes were made in the VIRT Subroutine: 1. A dummy variable was introduced by adding a new line of code after line VIR00420 that reads: REAL izlstemp xxx00420 2. The invalid virtual distance routine was removed by commenting out the following lines of code: IF(IZLS.LE.0.0) THEN VIR01040 M = IA(KST) VIR01050 L = IA(KST+1) - 1 VIR01060 DO 560 KK = M,L VIR01070 IF(SIGZS(KK).GT.SIGZWA) GO TO 570 VIR01080 560 CONTINUE VIR01090 570 VIRTZ = (SIGZWA*ASI(KK))**BSI(KK) VIR01100 ELSE The revised lines read as follows: c IF(IZLS.LE.0.0) THEN VIR01040 c M = IA(KST) VIR01050 c L = IA(KST+1) - 1 VIR01060 c DO 560 KK = M,L VIR01070 c IF(SIGZS(KK).GT.SIGZWA) GO TO 570 VIR01080 c560 CONTINUE VIR01090 c570 VIRTZ = (SIGZWA*ASI(KK))**BSI(KK) VIR01100 c ELSE VIR01110 3. New lines of code were added to assign appropriate values to the dummy variable for use in the revised virtual source routine. The following new lines of code were introduced after line VIR01110: IF(IZLS.LE.0.0) THEN XXX01110 izlstemp = BRIGGS(KST) XXX01111 ELSE XXX01112 izlstemp = IZLS XXX01113 ENDIF XXX01114 4. The variable, IZLS, was replaced by the new dummy variable, izlstemp, in the following lines of code: FRAC = SIGZWA/IZLS VIR01120 DENOM = IZLS - C1S*SIGZWA VIR01190 The lines were replaced with the following: c FRAC = SIGZWA/IZLS VIR01120 FRAC = SIGZWA/izlstemp XXX01120 and c DENOM = IZLS - C1S*SIGZWA VIR01190 DENOM = izlstemp - C1S*SIGZWA XXX01190 5. The ENDIF statement on line VIR01270 was commented out. The revised LINE of code is: C ENDIF XXX01270 6. The following IF statement was commented out and replaced with a new line of code: 600 IF(IZLS.GT.0.0.AND.DENOM.LE.0.0.AND.KST.GT.4) THEN VIR01290 The revised code is: C600 IF(IZLS.GT.0.0.AND.DENOM.LE.0.0.AND.KST.GT.4) THEN VIR01290 600 IF(DENOM.LE.0.0.AND.KST.GT.4) THEN XXX01290 7. The error in the mixing height subroutine was corrected by replacing the following line of code: IF(KST.LE.5) HTX2=AMIN1(HTX2,CAP) MIX00661 The line was replaced by the following: c IF(KST.LE.5) HTX2=AMIN1(HTX2,CAP) MIX00660 c The mixing height is capped if KST is 5 or 6 (stable) XXX00660 IF(KST.GE.5) HTX2=AMIN1(HTX2,CAP) XXX00661